View AD9434BCPZ-370_602491.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

12-Bit, 370 MSPS/500 MSPS, 1.8 V Analog-to-Digital Converter AD9434
FEATURES
SNR = 65 dBFS at fIN up to 250 MHz at 500 MSPS ENOB of 10.5 bits at fIN up to 250 MHz at 500 MSPS (-1.0 dBFS) SFDR = 78 dBc at fIN up to 250 MHz at 500 MSPS (-1.0 dBFS) Integrated input buffer Excellent linearity DNL = 0.5 LSB typical INL = 0.6 LSB typical LVDS at 500 MSPS (ANSI-644 levels) 1 GHz full power analog bandwidth On-chip reference, no external decoupling required Low power dissipation 690 mW at 500 MSPS--LVDS SDR mode 660 mW at 500 MSPS--LVDS DDR mode Programmable (nominal) input voltage range 1.18 V p-p to 1.6 V p-p, 1.5 V p-p nominal 1.8 V analog and digital supply operation Selectable output data format (offset binary, twos complement, Gray code) Clock duty cycle stabilizer Integrated data clock output with programmable clock and data alignment
FUNCTIONAL BLOCK DIAGRAM
VREF PWDN AGND AVDD
REFERENCE CML VIN+ VIN- TRACK-AND-HOLD ADC CORE CLK+ CLK- CLOCK MANAGEMENT 12
AD9434
DRVDD DRGND
OUTPUT 12 STAGING LVDS
D11 TO D0
OR+ OR- SERIAL PORT DCO+
09383-001
DCO- SCLK/DFS SDIO CSB
Figure 1.
APPLICATIONS
Wireless and wired broadband communications Cable reverse path Communications test equipment Radar and satellite subsystems Power amplifier linearization
Fabricated on an advanced BiCMOS process, the AD9434 is available in a 56-lead LFCSP, specified over the industrial temperature range (-40C to +85C). This part is protected under a U.S. patent.
PRODUCT HIGHLIGHTS
1. 2. 3. High Performance. Maintains 65 dBFS SNR at 500 MSPS with a 250 MHz input. Low Power. Consumes only 660 mW at 500 MSPS. Ease of Use. LVDS output data and output clock signal allow interface to FPGA technology. The on-chip reference and sampleand-hold provide flexibility in system design. Use of a single 1.8 V supply simplifies system power supply design. Serial Port Control. Standard serial port interface supports various product functions, such as data formatting, power-down, gain adjust, and output test pattern generation. The AD9434 is pin compatible with the AD9230, and can be substituted in many applications with minimal design changes.
GENERAL DESCRIPTION
The AD9434 is a 12-bit monolithic sampling analog-to-digital converter (ADC) optimized for high performance, low power, and ease of use. The part operates at up to a 500 MSPS conversion rate and is optimized for outstanding dynamic performance in wideband carrier and broadband systems. All necessary functions, including a sample-and-hold and voltage reference, are included on the chip to provide a complete signal conversion solution. The VREF pin can be used to monitor the internal reference or provide an external voltage reference (external reference mode must be enabled through the SPI port). The ADC requires a 1.8 V analog voltage supply and a differential clock for full performance operation. The digital outputs are LVDS (ANSI-644) compatible and support twos complement, offset binary format, or Gray code. A data clock output is available for proper output data timing.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.
4.
5.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)2011 Analog Devices, Inc. All rights reserved.
AD9434 TABLE OF CONTENTS
Features .............................................................................................. 1 Applications ....................................................................................... 1 General Description ......................................................................... 1 Functional Block Diagram .............................................................. 1 Product Highlights ........................................................................... 1 Revision History ............................................................................... 2 Specifications..................................................................................... 3 DC Specifications ......................................................................... 3 AC Specifications.......................................................................... 4 Digital Specifications ................................................................... 5 Switching Specifications .............................................................. 6 Timing Diagrams.......................................................................... 7 Absolute Maximum Ratings............................................................ 8 Thermal Resistance ...................................................................... 8 ESD Caution .................................................................................. 8 Pin Configurations and Function Descriptions ........................... 9 Typical Performance Characteristics ........................................... 13 Equivalent Circuits ......................................................................... 18 Theory of Operation ...................................................................... 19 Analog Input and Voltage Reference ....................................... 19 Clock Input Considerations ...................................................... 20 Power Dissipation and Power-Down Mode ........................... 21 Digital Outputs ........................................................................... 21 Timing ......................................................................................... 22 VREF ............................................................................................ 22 AD9434 Configuration Using the SPI ..................................... 22 Using the AD9434 to Replace the AD9230............................. 23 Hardware Interface..................................................................... 23 Configuration Without the SPI ................................................ 23 Memory Map .................................................................................. 25 Reading the Memory Map Table .............................................. 25 Reserved Locations .................................................................... 25 Default Values ............................................................................. 25 Logic Levels ................................................................................. 25 Outline Dimensions ....................................................................... 28 Ordering Guide .......................................................................... 28
REVISION HISTORY
5/11--Rev. 0 to Rev. A Changes to General Description .................................................... 1 Changes to Table 4, Aperture Time Values ................................... 6 Changes to Figure 32 ...................................................................... 17 Changes to Figure 42 ...................................................................... 19 Changes to Table 13, Register 10, Bits[7:0] Value, Register 14 Default Value, Register 15 Default Value, Register 17, Bit 7 Value and Register 18, Bit[4:0] Values .................................................... 26 3/11--Revision 0: Initial Version
Rev. A | Page 2 of 28
AD9434 SPECIFICATIONS
DC SPECIFICATIONS
AVDD = 1.8 V, DRVDD = 1.8 V, TMIN = -40C, TMAX = +85C, fIN = -1.0 dBFS, full scale = 1.5 V, unless otherwise noted. Table 1.
Parameter 1 RESOLUTION ACCURACY No Missing Codes Offset Error Gain Error Differential Nonlinearity (DNL) Integral Nonlinearity (INL) INTERNAL REFERENCE VREF TEMPERATURE DRIFT Offset Error Gain Error ANALOG INPUTS (VIN+, VIN-) Differential Input Voltage Range 2 Input Common-Mode Voltage Input Resistance (Differential) Input Capacitance (Differential) POWER SUPPLY AVDD DRVDD Supply Currents IAVDD 3 IDRVDD3/SDR Mode 4 IDRVDD3/DDR Mode 5 Power Dissipation SDR Mode4 DDR Mode5 Standby Mode Power-Down Mode
1 2 3
Temp
Min
AD9434-370 Typ Max 12 Guaranteed 0.25
Min
AD9434-500 Typ Max 12 Guaranteed 0.25
Unit Bits
Full 25C Full 25C Full 25C Full 25C Full Full Full Full Full Full Full 25C Full Full Full Full Full Full Full Full Full
-3.0 1.0 -5.0 0.4 -0.9 0.4 -0.92 0.71 0.75 18 0.07 1.18 1.5 1.7 1 1.3 1.8 1.8 260 88 70 625 595 40 2.5
+1.0 +7.0 +0.9 +0.92 0.78
-3.0 1.0 -5.0 0.5 -0.95 0.6 -1.3 0.71 0.75 18 0.07
+1.0 +7.0 +1.0 +1.3 0.78
mV mV % FS % FS LSB LSB LSB LSB V V/C %/C
1.6
1.18
1.5 1.7 1 1.3 1.8 1.8 283 100 82 690 657 40 2.5
1.6
V p-p V k pF V V mA mA mA mW mW mW mW
1.75 1.75
1.9 1.9 280 100 80 685 648 50 7
1.75 1.75
1.9 1.9 301 114 96 747 715 50 7
See the AN-835 Application Note, Understanding High Speed ADC Testing and Evaluation, for a complete set of definitions and how these tests were completed. The input range is programmable through the SPI, and the range specified reflects the nominal values of each setting. See the Memory Map section. IAVDD and IDRVDD are measured with a -1 dBFS, 30.3 MHz sine input at rated sample rate. 4 Single data rate mode; this is the default mode of the AD9434. 5 Double data rate mode; user-programmable feature. See the Memory Map section.
Rev. A | Page 3 of 28
AD9434
AC SPECIFICATIONS
AVDD = 1.8 V, DRVDD = 1.8 V, TMIN = -40C, TMAX = +85C, fIN = -1.0 dBFS, full scale = 1.5 V, unless otherwise noted. Table 2.
Parameter 1 , 2 SNR fIN = 30.3 MHz fIN = 70.3 MHz fIN = 100.3 MHz fIN = 250.3 MHz fIN = 450.3 MHz SINAD fIN = 30.3 MHz fIN = 70.3 MHz fIN = 100.3 MHz fIN = 250.3 MHz fIN = 450.3 MHz EFFECTIVE NUMBER OF BITS (ENOB) fIN = 30.3 MHz fIN = 70.3 MHz fIN = 100.3 MHz fIN = 250.3 MHz fIN = 450.3 MHz WORST HARMONIC (SECOND or THIRD) fIN = 30.3 MHz fIN = 70.3 MHz fIN = 100.3 MHz fIN = 250.3 MHz fIN = 450.3 MHz SFDR fIN = 30.3 MHz fIN = 70.3 MHz fIN = 100.3 MHz fIN = 250.3 MHz fIN = 450.3 MHz WORST OTHER HARMONIC (SFDR EXCLUDING SECOND and THIRD) fIN = 30.3 MHz fIN = 70.3 MHz fIN = 100.3 MHz fIN = 250.3 MHz fIN = 450.3 MHz TWO-TONE IMD fIN1 = 119.5 MHz, fIN2 = 122.5 MHz ANALOG INPUT BANDWIDTH Full Power
1 2
Temp 25C 25C 25C Full 25C 25C 25C 25C 25C Full 25C 25C 25C 25C 25C 25C 25C 25C 25C 25C Full 25C 25C 25C 25C 25C Full 25C 25C 25C 25C 25C Full 25C 25C 25C 25C
Min
AD9434-370 Typ Max 66.3 66.2 66.1
Min
AD9434-500 Typ Max 65.9 65.9 65.8
Unit dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS dBFS Bits Bits Bits Bits Bits dBc dBc dBc dBc dBc dBc dBc dBc dBc dBc dBc dBc dBc dBc dBc dBc dBc dBc dBc GHz
65.3 65.5 64.0 66.1 66.1 66.0 65.2 65.3 63.7 10.7 10.7 10.7 10.6 10.3 -93 -89 -83 -75 -80 -78 89 88 83 75 79 78 -90 -90 -91 -75 -83 -82 -85 1
64.5 65.2 63.5 65.9 65.8 65.8 64.4 64.8 62.9 10.7 10.6 10.6 10.5 10.2 -93 -91 -87 -74 -78 -69 84 82 83 74 78 68 -85 -82 -84 -74 -85 -78 -85 1
All ac specifications tested by driving CLK+ and CLK- differentially. See the AN-835 Application Note, Understanding High Speed ADC Testing and Evaluation, for a complete set of definitions and how these tests were completed.
Rev. A | Page 4 of 28
AD9434
DIGITAL SPECIFICATIONS
AVDD = 1.8 V, DRVDD = 1.8 V, TMIN = -40C, TMAX = +85C, fIN = -1.0 dBFS, full scale = 1.5 V, unless otherwise noted. Table 3.
Parameter 1 CLOCK INPUTS Logic Compliance Internal Common-Mode Bias Differential Input Voltage High Level Input (VIH) Low Level Input (VIL) High Level Input Current (IIH) Low Level Input Current (IIL) Input Resistance (Differential) Input Capacitance LOGIC INPUTS Logic 1 Voltage Logic 0 Voltage Logic 1 Input Current (SDIO, CSB) Logic 0 Input Current (SDIO, CSB) Logic 1 Input Current (SCLK, PDWN) Logic 0 Input Current (SCLK, PDWN) Input Capacitance LOGIC OUTPUTS 2 VOD Differential Output Voltage VOS Output Offset Voltage Output Coding
1 2
Temp Full Full Full Full Full Full Full Full Full Full Full Full Full Full 25C Full Full
Min
AD9434-370 Typ Max CMOS/LVDS/LVPECL 0.9
Min
AD9434-500 Typ Max CMOS/LVDS/LVPECL 0.9
Unit
V V p-p V p-p A A k pF V V A A A A pF mV V
0.2 -1.8 -10 -10 8
10 4
1.8 -0.2 +10 +10 12
0.2 -1.8 -10 -10 8
10 4
1.8 -0.2 +10 +10 12
0.8 x DRVDD 0.2 x DRVDD 0 -60 50 0 4 247 1.125
0.8 x DRVDD 0.2 x DRVDD 0 -60 50 0 4
454 247 454 1.375 1.125 1.375 Twos complement, Gray code, or offset binary (default)
See the AN-835 Application Note, Understanding High Speed ADC Testing and Evaluation, for a complete set of definitions and how these tests were completed. LVDS RTERMINATION = 100 .
Rev. A | Page 5 of 28
AD9434
SWITCHING SPECIFICATIONS
AVDD = 1.8 V, DRVDD = 1.8 V, TMIN = -40C, TMAX = +85C, fIN = -1.0 dBFS, full scale = 1.5 V, unless otherwise noted. Table 4.
Parameter Maximum Conversion Rate Minimum Conversion Rate CLK+ Pulse Width High (tCH)1, 2 CLK+ Pulse Width Low (tCL) Output (LVDS--SDR Mode)1 Data Propagation Delay (tPD) Rise Time (tR) (20% to 80%) Fall Time (tF) (20% to 80%) DCO Propagation Delay (tCPD) Data to DCO Skew (tSKEW) Latency Output (LVDS--DDR Mode)2 Data Propagation Delay (tPD) Rise Time (tR) (20% to 80%) Fall Time (tF) (20% to 80%) DCO Propagation Delay (tCPD) Data to DCO Skew (tSKEW) Latency Aperture Time (tA) Aperture Uncertainty (Jitter, tJ)
1 2
Temp Full Full Full Full Full 25C 25C Full Full Full Full 25C 25C Full Full Full 25C 25C
Min 370 1.1 1.1
AD9434-370 Typ Max 50 11 11 0.85 0.15 0.15 0.6
Min 500 0.9 0.9
AD9434-500 Typ Max 50 11 11 0.85 0.15 0.15 0.6
Unit MSPS MSPS ns ns ns ns ns ns ns Cycles ns ns ns ns ns Cycles ns fs rms
0.15 15 0.6 0.15 0.15 0.6 -0.07 15 0.85 80
0.38
0.15 15 0.6 0.15 0.15 0.6
0.38
+0.07
-0.07 15 0.85 80
+0.07
See Figure 2. See Figure 3.
Rev. A | Page 6 of 28
AD9434
Timing Diagrams
N-1 N N+3 VIN+, VIN- N+1 N+2
tA
N+4 N+5
tCH
CLK+ CLK-
tCL
1/fS
tCPD
DCO+ DCO-
tSKEW tPD
Dx+ Dx-
09383-002
09383-003
N - 15
N - 14
N - 13
N - 12
N - 11
Figure 2. Single Data Rate Mode
N-1 N VIN+, VIN-
tA
N+3
N+4 N+5
N+1
N+2
tCH
CLK+ CLK-
tCL
1/fS
tCPD
DCO+ DCO-
tSKEW tPD
D0/D6+ D0/D6- D6 N - 15 D0 N - 14 D6 N - 14 D0 N - 13 D6 N - 13 D0 N - 12 D6 N - 12 D0 N - 11 D6 N - 11 D0 N - 10
D5/D11+ D5/D11-
D11 N - 15
D5 N - 14 6 LSBs
D11 N - 14 6 MSBs
D5 N - 13
D11 N - 13
D5 N - 12
D11 N - 12
D5 N - 11
D11 N - 11
D5 N - 10
Figure 3. Double Data Rate Mode
Rev. A | Page 7 of 28
AD9434 ABSOLUTE MAXIMUM RATINGS
Table 5.
Parameter Electrical AVDD to AGND DRVDD to DRGND AGND to DRGND AVDD to DRVDD D0+/D0- Through D11+/D11- to DRGND DCO+, DCO- to DRGND OR+, OR- to DRGND CLK+ to AGND CLK- to AGND VIN+ to AGND VIN- to AGND CML to AGND VREF to AGND SDIO to DRGND PDWN to AGND CSB to AGND SCLK/DFS to AGND Environmental Storage Temperature Range Operating Temperature Range Lead Temperature (Soldering, 10 sec) Junction Temperature Rating -0.3 V to +2.0 V -0.3 V to +2.0 V -0.3 V to +0.3 V -2.0 V to +2.0 V -0.3 V to DRVDD + 0.2 V -0.3 V to DRVDD + 0.2 V -0.3 V to DRVDD + 0.2 V -0.3 V to AVDD + 0.2 V -0.3 V to AVDD + 0.2 V -0.3 V to AVDD + 0.2 V -0.3 V to AVDD + 0.2 V -0.3 V to AVDD + 0.2 V -0.3 V to AVDD + 0.2 V -0.3 V to DRVDD + 0.2 V -0.3 V to DRVDD + 0.2 V -0.3 V to DRVDD + 0.2 V -0.3 V to DRVDD + 0.2 V -65C to +125C -40C to +85C 300C 150C
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
THERMAL RESISTANCE
The exposed paddle must be soldered to the ground plane for the LFCSP package. Soldering the exposed paddle to the PCB increases the reliability of the solder joints, maximizing the thermal capability of the package. Table 6.
Package Type 56-Lead LFCSP_VQ (CP-56-5) JA 23.7 JC 1.7 Unit C/W
Typical JA and JC are specified for a 4-layer board in still air. Airflow increases heat dissipation, effectively reducing JA. In addition, metal in direct contact with the package leads from metal traces, through holes, ground, and power planes reduces the JA.
ESD CAUTION
Rev. A | Page 8 of 28
AD9434 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
56 55 54 53 52 51 50 49 48 47 46 45 44 43 D2+ D2- D1+ D1- D0+ D0- DCO+ DCO- DRGND DRVDD AVDD CLK- CLK+ AVDD
D3- D3+ D4- D4+ D5- D5+ DRVDD DRGND D6- D6+ D7- D7+ D8- D8+
1 2 3 4 5 6 7 8 9 10 11 12 13 14
PIN 1 INDICATOR
AD9434
TOP VIEW (Not to Scale)
PIN 0 (EXPOSED PADDLE) = AGND
42 41 40 39 38 37 36 35 34 33 32 31 30 29
AVDD AVDD CML AVDD AVDD AVDD VIN- VIN+ AVDD AVDD AVDD VREF AVDD PWDN
NOTES 1. DNC = DO NOT CONNECT. DO NOT CONNECT TO THIS PIN. 2. AGND AND DRGND SHOULD BE TIED TO A COMMON QUIET GROUND PLANE. 3. THE EXPOSED PADDLE MUST BE SOLDERED TO A GROUND PLANE.
D9- D9+ D10- D10+ D11- D11+ OR- OR+ DRGND DRVDD SDIO SCLK/DFS CSB DNC
15 16 17 18 19 20 21 22 23 24 25 26 27 28
Figure 4. Pin Configuration--Single Data Rate Mode
Table 7. Pin Function Descriptions--Single Data Rate Mode
Pin No. 0 30, 32 to 34, 37 to 39, 41 to 43, 46 7, 24, 47 8, 23, 48 35 36 40 44 45 31 28 25 26 27 29 49 50 51 52 53 54 55 56 1 2 3 Mnemonic AGND 1 AVDD DRVDD DRGND1 VIN+ VIN- CML CLK+ CLK- VREF DNC SDIO SCLK/DFS CSB PWDN DCO- DCO+ D0- D0+ D1- D1+ D2- D2+ D3- D3+ D4- Description Analog Ground. The exposed paddle must be soldered to a ground plane. 1.8 V Analog Supply. 1.8 V Digital Output Supply. Digital Output Ground. Analog Input--True. Analog Input--Complement. Common-Mode Output. Enabled through the SPI, this pin provides a reference for the optimized internal bias voltage for VIN+/VIN-. Clock Input--True. Clock Input--Complement. Voltage Reference Internal/Input/Output. Nominally 0.75 V. Do Not Connect. Do not connect to this pin. This pin should be left floating. Serial Port Interface (SPI) Data Input/Output (Serial Port Mode). Serial Port Interface Clock (Serial Port Mode)/Data Format Select (External Pin Mode). Serial Port Chip Select (Active Low). Chip Power-Down. Data Clock Output--Complement. Data Clock Output--True. D0 Complement Output (LSB). D0 True Output (LSB). D1 Complement Output. D1 True Output. D2 Complement Output. D2 True Output. D3 Complement Output. D3 True Output. D4 Complement Output.
Rev. A | Page 9 of 28
09383-004
AD9434
Pin No. 4 5 6 9 10 11 12 13 14 15 16 17 18 19 20 21 22
1
Mnemonic D4+ D5- D5+ D6- D6+ D7- D7+ D8- D8+ D9- D9+ D10- D10+ D11- D11+ OR- OR+
Description D4 True Output. D5 Complement Output. D5 True Output. D6 Complement Output. D6 True Output. D7 Complement Output. D7 True Output. D8 Complement Output. D8 True Output. D9 Complement Output. D9 True Output. D10 Complement Output. D10 True Output. D11 Complement Output (MSB). D11 True Output (MSB). Overrange Complement Output. Overrange True Output.
AGND and DRGND should be tied to a common quiet ground plane.
Rev. A | Page 10 of 28
AD9434
D2/D8+ D2/D8- D1/D7+ D1/D7- D0/D6+ D0/D6- DCO+ DCO- DRGND DRVDD AVDD CLK- CLK+ AVDD
D3/D9- D3/D9+ D4/D10- D4/D10+ D5/D11- D5/D11+ DRVDD DRGND OR- OR+ DNC DNC DNC DNC
1 2 3 4 5 6 7 8 9 10 11 12 13 14
56 55 54 53 52 51 50 49 48 47 46 45 44 43
PIN 1 INDICATOR
AD9434
TOP VIEW (Not to Scale)
PIN 0 (EXPOSED PADDLE) = AGND
42 41 40 39 38 37 36 35 34 33 32 31 30 29
AVDD AVDD CML AVDD AVDD AVDD VIN- VIN+ AVDD AVDD AVDD VREF AVDD PWDN
NOTES 1. DNC = DO NOT CONNECT. DO NOT CONNECT TO THIS PIN. 2. AGND AND DRGND SHOULD BE TIED TO A COMMON QUIET GROUND PLANE. 3. THE EXPOSED PADDLE MUST BE SOLDERED TO A GROUND PLANE.
DNC DNC DNC DNC DNC DNC DNC/(OR-) DNC/(OR+) DRGND DRVDD SDIO SCLK/DFS CSB DNC
15 16 17 18 19 20 21 22 23 24 25 26 27 28
Figure 5. Pin Configuration--Double Data Rate Mode
Table 8. Pin Function Descriptions--Double Data Rate Mode
Pin No. 0 30, 32 to 34, 37 to 39, 41 to 43, 46 7, 24, 47 8, 23, 48 35 36 40 44 45 31 25 26 27 29 49 50 51 52 53 54 55 56 1 2 3 4 5 Mnemonic AGND 1 AVDD DRVDD DRGND1 VIN+ VIN- CML CLK+ CLK- VREF SDIO SCLK/DFS CSB PWDN DCO- DCO+ D0/D6- D0/D6+ D1/D7- D1/D7+ D2/D8- D2/D8+ D3/D9- D3/D9+ D4/D10- D4/D10+ D5/D11- Description Analog Ground. The exposed paddle must be soldered to a ground plane. 1.8 V Analog Supply. 1.8 V Digital Output Supply. Digital Output Ground. Analog Input--True. Analog Input--Complement. Common-Mode Output. Enabled through the SPI, this pin provides a reference for the optimized internal bias voltage for VIN+/VIN-. Clock Input--True. Clock Input--Complement. Voltage Reference Internal/Input/Output. Nominally 0.75 V. Serial Port Interface (SPI) Data Input/Output (Serial Port Mode). Serial Port Interface Clock (Serial Port Mode)/Data Format Select (External Pin Mode). Serial Port Chip Select (Active Low). Chip Power-Down. Data Clock Output--Complement. Data Clock Output--True. D0/D6 Complement Output (LSB). D0/D6 True Output (LSB). D1/D7 Complement Output. D1/D7 True Output. D2/D8 Complement Output. D2/D8 True Output. D3/D9 Complement Output. D3/D9 True Output. D4/D10 Complement Output. D4/D10 True Output. D5/D11 Complement Output (MSB).
Rev. A | Page 11 of 28
09383-005
AD9434
Pin No. 6 9 10 11 to 20, 28 21 22
1
Mnemonic D5/D11+ OR- OR+ DNC DNC/(OR-) DNC/(OR+)
Description D5/D11 True Output (MSB). Overrange Complement Output. (This pin is disabled if Pin 21 is reconfigured through the SPI to be OR-.) Overrange True Output. (This pin is disabled if Pin 22 is reconfigured through the SPI to be OR+.) Do Not Connect. Do not connect to these pins. These pins should be left floating. Do Not Connect. Do not connect to this pin. (This pin can be reconfigured as the overrange complement output through the serial port register.) Do Not Connect. Do not connect to this pin. (This pin can be reconfigured as the overrange true output through the serial port register.)
Tie AGND and DRGND to a common quiet ground plane.
Rev. A | Page 12 of 28
AD9434 TYPICAL PERFORMANCE CHARACTERISTICS
AVDD = 1.8 V, DRVDD = 1.8 V, rated sample rate, TA = 25C, 1.5 V p-p differential input, AIN = -1 dBFS, unless otherwise noted.
0 370MSPS 30.3MHz AT -1.0dBFS SNR: 65.4dB ENOB: 10.7 BITS SFDR: 90dBc 0 500MSPS 30.3MHz AT -1.0dBFS SNR: 65.0dB ENOB: 10.7 BITS SFDR: 85dBc
-20
-20
AMPLITUDE (dBFS)
-40
AMPLITUDE (dBFS)
09383-106
-40
-60
-60
-80
-80
-100
-100
0
20
40
60
80 100 120 FREQUENCY (MHz)
140
160
180
0
20
40
60
80
100 120 140 160 180 200 220 240 FREQUENCY (MHz)
Figure 6. AD9434-370 64k Point Single-Tone FFT; 370 MSPS, 30.3 MHz
0 370MSPS 100.3MHz AT -1.0dBFS SNR: 65.3dB ENOB: 10.7 BITS SFDR: 83dBc
Figure 9. AD9434-500 64k Point Single-Tone FFT; 500 MSPS, 30.3 MHz
0 500MSPS 100.3MHz AT -1.0dBFS SNR: 64.9dB ENOB: 10.6 BITS SFDR: 84dBc
-20
-20
AMPLITUDE (dBFS)
-40
AMPLITUDE (dBFS)
-40
-60
-60
-80
-80
-100
-100
09383-107
0
20
40
60
80 100 120 FREQUENCY (MHz)
140
160
180
0
20
40
60
80
100 120 140 160 180 200 220 240 FREQUENCY (MHz)
Figure 7. AD9434-370 64k Point Single-Tone FFT; 370 MSPS, 100.3 MHz
0 370MSPS 140.3MHz AT -1.0dBFS SNR: 65.2dB ENOB: 10.7 BITS SFDR: 85dBc
Figure 10. AD9434-500 64k Point Single-Tone FFT; 500 MSPS, 100.3 MHz
0 500MSPS 140.3MHz AT -1.0dBFS SNR: 64.8dB ENOB: 10.6 BITS SFDR: 79dBc
-20
-20
AMPLITUDE (dBFS)
-40
AMPLITUDE (dBFS)
-40
-60
-60
-80
-80
-100
-100
09383-108
0
20
40
60
80 100 120 FREQUENCY (MHz)
140
160
180
0
20
40
60
80
100 120 140 160 180 200 220 240 FREQUENCY (MHz)
Figure 8. AD9434-370 64k Point Single-Tone FFT; 370 MSPS, 140.3 MHz
Figure 11. AD9434-500 64k Point Single-Tone FFT; 500 MSPS, 140.3 MHz
Rev. A | Page 13 of 28
09383-111
-120
-120
09383-110
-120
-120
09383-109
-120
-120
AD9434
0 491.52MSPS 368.3MHz AT -1.0dBFS SNR: 64.0dB ENOB: 10.5 BITS SFDR: 79dBc
90 SFDR (dBc), TA = -40C 85 80
SNR/SFDR (dB)
-20
SFDR (dBc), TA = +25C
AMPLITUDE (dBFS)
-40
75 70 65 60 SNR (dBFS), TA = +25C SNR (dBFS), TA = +85C SFDR (dBc), TA = +85C SNR (dBFS), TA = -40C
-60
-80
-100
55 50 0 50 100 150 200 250 300 350 400 450 500 ANALOG INPUT FREQUECY (MHz)
09383-112
0
20
40
60
80
100 120 140 160 180 200 220 240 FREQUENCY (MHz)
Figure 12. AD9434-500 64k Point Single-Tone; 491.52 MSPS, 368.3 MHz
0 491.52MSPS 450.3MHz AT -1.0dBFS SNR: 63.5dB ENOB: 10.3 BITS SFDR: 72dBc
Figure 15. AD9434-500 Single-Tone SNR/SFDR vs. Input Frequency (fIN) and Temperature; 500 MSPS
100 SFDR (dBc), 30.3MHz 90
-20
AMPLITUDE (dBFS)
SNR/SFDR (dB)
-40
80 SFDR (dBc), 100.3MHz 70 SNR (dBFS), 30.3MHz
-60
-80
60
SNR (dBFS), 100.3MHz
-100
50
09383-113
0
20
40
60
80
100 120 140 160 180 200 220 240 FREQUENCY (MHz)
100
150
200
250
300
350
400
450
500
550
SAMPLE RATE (MSPS)
Figure 13. AD9434-500 64k Point Single-Tone; 491.52 MSPS, 450.3 MHz
100 95 90 85 SFDR (dBc), TA = -40C SFDR (dBc), TA = +25C
Figure 16. AD9434-370 SNR/SFDR vs. Sample Rate; 30.3 MHz, 100.3 MHz
100 SFDR (dBc), 30.3MHz 90
SNR/SFDR (dB)
SNR/SFDR (dB)
80 SFDR (dBc), 100.3MHz SNR (dBFS), 30.3MHz 70
80 75 70 65 60 55 SNR (dBFS), TA = +25C SNR (dBFS), TA = +85C SFDR (dBc), TA = +85C SNR (dBFS), TA = -40C
60 SNR (dBFS), 100.3MHz 50
100
150
200
250
300
350
400
450
500
550
ANALOG INPUT FREQUECY (MHz)
SAMPLE RATE (MSPS)
Figure 14. AD9434-370 Single-Tone SNR/SFDR vs. Input Frequency (fIN) and Temperature; 370 MSPS
Figure 17. AD9434-500 SNR/SFDR vs. Sample Rate; 30.3 MHz, 100.3 MHz
Rev. A | Page 14 of 28
09383-117
0
50
100
150
200
250
300
350
400
450
500
09383-114
50
40 50
09383-116
-120
40 50
09383-115
-120
AD9434
100 90 80 70 SNR (dBFS) SFDR (dBFS)
0.8 0.6 0.4 0.2
SNR/SFDR (dB)
50 40 30 20 10 -80 -70 -60 -50 -40 -30 -20 -10 0
09383-118
INL (LSB)
60
0 -0.2
SFDR (dBc)
SNR (dB)
-0.4 -0.6
09383-121 09383-123 09383-122
0 -90
-0.8 -1
1023
2047 OUTPUT CODE
3071
4095
AMPLITUDE (dB)
Figure 18. AD9434-370 SNR/SFDR vs. Input Amplitude; 500 MSPS, 140.3 MHz
100 90 SFDR (dBFS) 80 70 SNR (dBFS)
Figure 21. AD9434-500 INL; 500 MSPS
0.4 0.3 0.2 0.1 0 -0.1 -0.2 -0.3
SNR/SFDR (dB)
50 40 30 20 10 -80 -70 -60 -50 -40 -30 -20 -10 0
09383-119
SFDR (dBc)
SNR (dB)
0 -90
DNL (LSB)
60
-0.4 -1
1023
2047 OUTPUT CODE
3071
4095
AMPLITUDE (dB)
Figure 19. AD9434-500 SNR/SFDR vs. Input Amplitude; 500 MSPS, 140.3 MHz
0.5 0.4 0.3 0.2 0.6 0.5 0.4 0.3
Figure 22. AD9434-370 DNL; 370 MSPS
0 -0.1 -0.2 -0.3 -0.4 1023 2047 OUTPUT CODE 3071 4095
09383-120
DNL (LSB)
INL (LSB)
0.1
0.2 0.1 0 -0.1 -0.2 -0.3 -0.4 -1 1023 2047 OUTPUT CODE 3071 4095
-0.5 -1
Figure 20. AD9434-370 INL; 370 MSPS
Figure 23. AD9434-500 DNL, 500 MSPS
Rev. A | Page 15 of 28
AD9434
2.5 1.17LSB rms 2.0
0 500MSPS fIN1 = 119.5MHz AT -7.0dBFS fIN2 = 122.5MHz AT -7.0dBFS SFDR: 86dBc
-20
NUMBER OF HITS (M)
1.5
AMPLITUDE (dB)
09383-124
-40
-60
1.0
-80
0.5
-100
N-3
N-2
N-1
N
N+1 BINS
N+2
N+3
MORE
0
50
100
150
200
250
FREQUENCY (MHz)
Figure 24. AD9434-370 Grounded Input Histogram; 370 MSPS
Figure 27. AD9434-500 64k Point, Two-Tone FFT; 500 MSPS, 119.2 MHz, 122.5 MHz
120
2.5 1.24LSB rms 2.0
IMD3 (dBFS)
100
SFDR (dBFS)
NUMBER OF HITS (M)
80
SFDR (dB)
1.5
60
SFDR (dBc)
1.0
40
0.5
20
09383-125
N-3
N-2
N-1
N
N+1 BINS
N+2
N+3
MORE
-80
-70
-60
-50
-40
-30
-20
-10
0
AMPLITUDE (dBFS)
Figure 25. AD9434-500 Grounded Input Histogram; 500 MSPS
0 370MSPS fIN1 = 119.5MHz AT -7.0dBFS fIN2 = 122.5MHz AT -7.0dBFS SFDR: 82dBc
Figure 28. AD9434-370 Two-Tone SFDR vs. Input Amplitude; 370 MSPS, 119.5 MHz, 122.5 MHz
120 IMD3 (dBFS) 100 SFDR (dBFS)
-20
AMPLITUDE (dB)
-40
80
SFDR (dB)
-60
60 SFDR (dBc) 40
-80
-100
20
09383-126
0
50
100 FREQUENCY (MHz)
150
-80
-70
-60
-50
-40
-30
-20
-10
0
AMPLITUDE (dBFS)
Figure 26. AD9434-370 64k Point, Two-Tone FFT; 370 MSPS, 119.5 MHz, 122.5 MHZ
Figure 29. AD9434-500 Two-Tone SFDR vs. Input Amplitude; 500 MSPS, 119.5 MHz, 122.5 MHz
Rev. A | Page 16 of 28
09383-129
-120
0 -90
09383-128
0
0 -90
09383-127
0
-120
AD9434
90 85 80
80
SFDR (dBc)
SFDR (dBc)
75
SNR/SFDR (dB)
75 70 65 60 55 50 1.5
AD9434, 370MSPS
SNR/SFDR (dB)
70
AD9434, 370MSPS
65
SNR (dBFS)
SNR (dBFS)
AD9434, 500MSPS
60
AD9434, 500MSPS
55
VCM (V)
09383-130
1.6
1.7
1.8
1.9
2.0
600
700
800
900
1000
ANALOG INPUT FREQUENCY (MHz)
Figure 30. SNR/SFDR vs. Common-Mode Voltage; 370 MSPS, 500 MSPS, fIN = 140.3 MHz
350 TOTAL POWER 800 700 600
CURRENT (mA)
Figure 32. SNR/SFDR for AD9434-370 and AD9434-500 at 370 MSPS and 500 MSPS; AIN Sweep at -1.0 dBFS
300
250 IAVDD 200
400 300 200
150
100
IDRVDD
100 0
50
50 75 100 125 150 175 200 225 250 275 300 325 350 375 400 425 450 475 500 525 550
POWER (mW)
500
SAMPLE RATE (MSPS)
Figure 31. Current and Power vs. Sample Rate, fIN = 30.3 MHz
Rev. A | Page 17 of 28
09383-131
09383-132
50 500
AD9434 EQUIVALENT CIRCUITS
AVDD
DRVDD
AVDD 0.9V CLK+ 15k 15k CLK- AVDD
DRVDD 30k CSB
09383-006
DRVDD
350
Figure 33. Clock Inputs
VBOOST AVDD
Figure 37. Equivalent CSB Input Circuit
DRVDD
CML
V+ D11- TO D0-
AVDD
V- D11+ TO D0+ V+
V-
AIN+ 500 DC
Figure 38. LVDS Outputs (Dx+, Dx-, OR+, OR-, DCO+, DCO-)
AVDD SPI CONTROLLED VIN+
500
AVDD
AIN-
09383-007
(00)
20k (01)
VREF (10) NOT USED (11) SPI CTRL VREF SELECT 00 = INTERNAL VREF 01 = IMPORT VREF 10 = EXPORT VREF 11 = NOT USED
Figure 34. Analog Input DC Equivalent Circuit (VCML = ~1.7 V)
DRVDD
09383-010
VIN+
09383-009
DRVDD SCLK/DFS 350 30k
09383-008
Figure 39. Equivalent VREF Input/Output Circuit
DRVDD DRVDD 350 30k
Figure 35. Equivalent SCLK/DFS, PDWN Input Circuit
VIN+
SDIO
1.3pF 1000
09383-011
09383-025
VIN-
CTRL
Figure 36. Analog Input AC Equivalent Circuit
Figure 40. Equivalent SDIO Input Circuit
Rev. A | Page 18 of 28
09383-012
AD9434 THEORY OF OPERATION
The AD9434 architecture consists of a front-end sample-andhold amplifier (SHA) followed by a pipelined switched capacitor ADC. The quantized outputs from each stage are combined into a final 12-bit result in the digital correction logic. The pipelined architecture permits the first stage to operate on a new input sample, whereas the remaining stages operate on preceding samples. Sampling occurs on the rising edge of the clock. Each stage of the pipeline, excluding the last, consists of a low resolution flash ADC connected to a switched capacitor DAC and interstage residue amplifier (MDAC). The residue amplifier magnifies the difference between the reconstructed DAC output and the flash input for the next stage in the pipeline. One bit of redundancy is used in each stage to facilitate digital correction of flash errors. The last stage simply consists of a flash ADC. The input stage contains a differential SHA that can be ac- or dc-coupled in differential or single-ended mode. The output staging block aligns the data, carries out the error correction, and passes the data to the output buffers. The output buffers are powered from a separate supply, allowing adjustment of the output voltage swing. During power-down, the output buffers enter a high impedance state.
Differential Input Configurations
Optimum performance is achieved while driving the AD9434 in a differential input configuration. For baseband applications, the AD8138 differential driver provides excellent performance and a flexible interface to the ADC. The output common-mode voltage of the AD8138 is easily set to AVDD/2 + 0.5 V, and the driver can be configured in a Sallen-Key filter topology to provide band limiting of the input signal.
1V p-p 49.9 499 499 523 0.1F 33 499 33 AVDD VIN+
AD8138
20pF
AD9434
VIN-
09383-013
CML
Figure 41. Differential Input Configuration Using the AD8138
ANALOG INPUT AND VOLTAGE REFERENCE
The analog input to the AD9434 is a differential buffer. For best dynamic performance, match the source impedances driving VIN+ and VIN- such that common-mode settling errors are symmetrical. The analog input is optimized to provide superior wideband performance and requires that the analog inputs be driven differentially. SNR and SINAD performance degrades significantly if the analog input is driven with a single-ended signal. A wideband transformer, such as Mini-Circuits(R) ADT1-1WT, can provide the differential analog inputs for applications that require a single-ended-to-differential conversion. Both analog inputs are self-biased by an on-chip reference to a nominal 1.7 V. An internal differential voltage reference creates positive and negative reference voltages that define the 1.5 V p-p fixed span of the ADC core. This internal voltage reference can be adjusted by means of an SPI control. See the AD9434 Configuration Using the SPI section for more details.
At input frequencies in the second Nyquist zone and above, the performance of most amplifiers may not be adequate to achieve the true performance of the AD9434. This is especially true in IF undersampling applications where frequencies in the 70 MHz to 100 MHz range are being sampled. For these applications, differential transformer coupling is the recommended input configuration. The signal characteristics must be considered when selecting a transformer. Most RF transformers saturate at frequencies below a few megahertz (MHz), and excessive signal power can cause core saturation, which leads to distortion. In any configuration, the value of the shunt capacitor, C (see Figure 43), is dependent on the input frequency and may need to be reduced or removed.
15 1.5V p-p 50 2pF VIN+
AD9434
VIN-
09383-014
15 0.1F
Figure 42. Differential Transformer--Coupled Configuration
As an alternative to using a transformer-coupled input at frequencies in the second Nyquist zone, the AD8352 differential driver can be used (see Figure 43).
Rev. A | Page 19 of 28
AD9434
VCC
0.1F 0.1F ANALOG INPUT 0 16 1 2 200 CD RD RG 3 ANALOG INPUT 0.1F 0 4 5 14 10
09383-015
8, 13 11
0.1F
R VIN+ C R
AD8352
0.1F
200
AD9434
VIN- CML
0.1F
0.1F
Figure 43. Differential Input Configuration Using the AD8352
CLOCK INPUT CONSIDERATIONS
For optimum performance, drive the AD9434 sample clock inputs (CLK+ and CLK-) with a differential signal. This signal is typically ac-coupled into the CLK+ and CLK- pins via a transformer or capacitors. These pins are biased at ~0.9 V internally and require no additional bias. If the clock signal is dc-coupled, then the common-mode voltage should remain within a range of 0.9 V. Figure 44 shows one preferred method for clocking the AD9434. The low jitter clock source is converted from single-ended to differential using an RF transformer. The back-to-back Schottky diodes across the secondary transformer limit clock excursions into the AD9434 to approximately 0.8 V p-p differential. This helps prevent the large voltage swings of the clock from feeding through to other portions of the AD9434 and preserves the fast rise and fall times of the signal, which are critical to low jitter performance.
MINI-CIRCUITS ADT1-1WT, 1:1Z 0.1F XFMR 100 0.1F 0.1F SCHOTTKY DIODES: HSM2812
CLOCK INPUT 0.1F
AD9510/AD9511/ AD9512/AD9513/ AD9514/AD9515
0.1F CLK PECL DRIVER CLK 501 240 240
09383-017
CLK+ 100 0.1F
CLOCK INPUT 501
0.1F
AD9434
CLK-
ADC
150 RESISTORS ARE OPTIONAL.
Figure 45. Differential PECL Sample Clock
AD9510/AD9511/ AD9512/AD9513/ AD9514/AD9515
CLOCK INPUT 0.1F CLK LVDS DRIVER CLK 501
09383-018
0.1F CLK+ 100 0.1F
CLOCK INPUT 501
0.1F
AD9434
CLK-
ADC
150 RESISTORS ARE OPTIONAL.
Figure 46. Differential LVDS Sample Clock
0.1F CLOCK INPUT 50
CLK+
AD9434
CLK-
09383-016
ADC
In some applications, it may be acceptable to drive the sample clock inputs with a single-ended 1.8 V CMOS signal. In such applications, drive the CLK+ pin directly from a CMOS gate, and bypass the CLK- pin to ground with a 0.1 F capacitor in parallel with a 39 k resistor (see Figure 47).
VCC 0.1F CLOCK INPUT 501 1k 1k AD951x CMOS DRIVER OPTIONAL 0.1F 100 CLK+
Figure 44. Transformer-Coupled Differential Clock
150
RESISTOR IS OPTIONAL.
Figure 47. Single-Ended 1.8 V CMOS Input Clock (Up to 200 MHz)
Rev. A | Page 20 of 28
09383-024
If a low jitter clock is available, another option is to ac couple a differential PECL signal to the sample clock input pins, as shown in Figure 45. The AD9510/AD9511/AD9512/AD9513/ AD9514/AD9515 family of clock drivers offers excellent jitter performance.
ADC AD9434
CLK- 0.1F 39k
AD9434
Clock Duty Cycle Considerations
Typical high speed ADCs use both clock edges to generate a variety of internal timing signals. As a result, these ADCs may be sensitive to clock duty cycle. A 5% tolerance is commonly required on the clock duty cycle to maintain dynamic performance characteristics. The AD9434 contains a duty cycle stabilizer (DCS) that retimes the nonsampling edge, providing an internal clock signal with a nominal 50% duty cycle. This allows a wide range of clock input duty cycles without affecting the performance of the AD9434. The duty cycle stabilizer uses a delay-locked loop (DLL) to create the nonsampling edge. As a result, any changes to the sampling frequency require approximately 5 s to allow the DLL to acquire and lock to the new rate.
POWER DISSIPATION AND POWER-DOWN MODE
As shown in Figure 31, the power dissipated by the AD9434 is proportional to its sample rate. The digital power dissipation does not vary much because it is determined primarily by the DRVDD supply and bias current of the LVDS output drivers. By asserting PDWN (Pin 29) high, the AD9434 is placed in standby mode or full power-down mode, as determined by the contents of Serial Port Register 08. Reasserting the PDWN pin low returns the AD9434 to its normal operational mode. An additional standby mode is supported by means of varying the clock input. When the clock rate falls below 50 MHz, the AD9434 assumes a standby state. In this case, the biasing network and internal reference remain on, but digital circuitry is powered down. Upon reactivating the clock, the AD9434 resumes normal operation after allowing for the pipeline latency.
Clock Jitter Considerations
High speed, high resolution ADCs are sensitive to the quality of the clock input. The degradation in SNR at a given input frequency (fA) due only to aperture jitter (tJ) can be calculated by SNR Degradation = 20 x log10(1/2 x x fA x tJ) In this equation, the rms aperture jitter represents the root mean square of all jitter sources, including the clock input, analog input signal, and ADC aperture jitter specifications. IF undersampling applications are particularly sensitive to jitter (see Figure 48). Treat the clock input as an analog signal in cases where aperture jitter may affect the dynamic range of the AD9434. Separate power supplies for clock drivers from the ADC output driver supplies to avoid modulating the clock signal with digital noise. Low jitter, crystal-controlled oscillators make the best clock sources. If the clock is generated from another type of source (by gating, dividing, or other methods), it should be retimed by the original clock at the last step. Refer to the AN-501 Application Note and the AN-756 Application Note for more in-depth information about jitter performance as it relates to ADCs (visit www.analog.com).
130 120 110 100
SNR (dB)
DIGITAL OUTPUTS
Digital Outputs and Timing
The AD9434 differential outputs conform to the ANSI-644 LVDS standard on default power-up. This can be changed to a low power, reduced signal option similar to the IEEE 1596.3 standard using the SPI. This LVDS standard can further reduce the overall power dissipation of the device, which reduces the power by ~39 mW. See the Memory Map section for more information. The LVDS driver current is derived on chip and sets the output current at each output equal to a nominal 3.5 mA. A 100 differential termination resistor placed at the LVDS receiver inputs results in a nominal 350 mV swing at the receiver. The AD9434 LVDS outputs facilitate interfacing with LVDS receivers in custom ASICs and FPGAs that have LVDS capability for superior switching performance in noisy environments. Single point-to-point net topologies are recommended with a 100 termination resistor placed as close to the receiver as possible. No far end receiver termination or poor differential trace routing may result in timing errors. It is recommended that the trace length be no longer than 24 inches and that the differential output traces be kept close together and at equal lengths. An example of the LVDS output using the ANSI standard (default) data eye and a time interval error (TIE) jitter histogram with trace lengths less than 24 inches on regular FR-4 material is shown in Figure 49. Figure 50 shows an example of when the trace lengths exceed 24 inches on regular FR-4 material. Notice that the TIE jitter histogram reflects the decrease of the data eye opening as the edge deviates from the ideal position. It is up to the user to determine if the waveforms meet the timing budget of the design when the trace lengths exceed 24 inches.
RMS CLOCK JITTER REQUIREMENT
16 BITS 14 BITS 12 BITS 10 BITS 8 BITS 0.125ps 0.25ps 0.5ps 1.0ps 2.0ps
90 80 70 60 50 40 30
1
10 100 ANALOG INPUT FREQUENCY (MHz)
1000
Figure 48. Ideal SNR vs. Input Frequency and Jitter
Rev. A | Page 21 of 28
09383-019
AD9434
14 500
EYE DIAGRAM: VOLTAGE (mV)
Out-of-Range (OR)
An out-of-range condition exists when the analog input voltage is beyond the input range of the ADC. OR+ and OR- (OR) are digital outputs that are updated along with the data output corresponding to the particular sampled input voltage. Thus, OR has the same pipeline latency as the digital data. OR is low when the analog input voltage is within the analog input range and high when the analog input voltage exceeds the input range, as shown in Figure 51. OR remains high until the analog input returns to within the input range and another conversion is completed. By logically AND'ing OR with the MSB and its complement, overrange high or underrange low conditions can be detected.
OR DATA OUTPUTS 1 1111 1111 1111 0 1111 1111 1111 0 1111 1111 1110 +FS - 1 LSB OR
400 300 200 100 0 -100 -200 -300 -400 -500 -3 -2 -1 0 1 2 3
TIE JITTER HISTOGRAM (Hits)
12 10 8 6 4 2 0 -40
-20
0 TIME (ps)
20
40
TIME (ns)
Figure 49. Data Eye for LVDS Outputs in ANSI Mode with Trace Lengths Less than 24 Inches on Standard FR-4, AD9434-500
600 12
09383-020
-FS + 1/2 LSB 0 0 1 0000 0000 0001 0000 0000 0000 0000 0000 0000 -FS -FS - 1/2 LSB +FS +FS - 1/2 LSB
09383-022
400
EYE DIAGRAM: VOLTAGE (mV)
10
200
TIE JITTER HISTOGRAM (Hits)
8
0
6
Figure 51. OR Relation to Input Voltage and Output Data
-200
4
TIMING
The AD9434 provides latched data outputs with a pipeline delay of seven clock cycles. Data outputs are available one propagation delay (tPD) after the rising edge of the clock signal.
0 TIME (ps) 100
-400
2
-2
-1
0
1
2
3
TIME (ns)
Figure 50. Data Eye for LVDS Outputs in ANSI Mode with Trace Lengths Greater than 24 Inches on Standard FR-4, AD9434-500
The format of the output data is offset binary by default. An example of the output coding format can be found in Table 12. If it is desired to change the output data format to twos complement, see the AD9434 Configuration Using the SPI section. An output clock signal is provided to assist in capturing data from the AD9434. The DCO is used to clock the output data and is equal to the sampling clock (CLK) rate. In single data rate mode (SDR), data is clocked out of the AD9434 and must be captured on the rising edge of the DCO. In double data rate mode (DDR), data is clocked out of the AD9434 and must be captured on the rising and falling edges of the DCO. See the timing diagrams shown in Figure 2 and Figure 3 for more information.
09383-021
-600 -3
0 -100
Minimize the length of the output data lines and loads placed on them to reduce transients within the AD9434. These transients can degrade the dynamic performance of the converter. The AD9434 also provides a data clock output (DCO) intended for capturing the data in an external register. The data outputs are valid on the rising edge of DCO. The lowest conversion rate of the AD9434 is 50 MSPS. At clock rates below 1 MSPS, the AD9434 assumes the standby mode.
VREF
The AD9434 VREF pin (Pin 31) allows the user to monitor the on-board voltage reference, or provide an external reference (requires configuration through the SPI). The three optional settings are internal VREF (pin is connected to 20 k to ground), export VREF, and import VREF. Do not attach a bypass capacitor to this pin. VREF is internally compensated and additional loading may impact performance.
Output Data Rate and Pinout Configuration
The output data of the AD9434 can be configured to drive 12 pairs of LVDS outputs at the same rate as the input clock signal (SDR mode), or six pairs of LVDS outputs at 2x the rate of the input clock signal (DDR mode). SDR is the default mode; the device can be reconfigured for DDR by setting Bit 3 in Register 14 (see Table 13).
AD9434 CONFIGURATION USING THE SPI
The AD9434 SPI allows the user to configure the converter for specific functions or operations through a structured register space inside the ADC. This gives the user added flexibility to customize device operation depending on the application. Addresses are accessed (programmed or readback) serially in 1-byte words. Each byte can be further divided into fields, which are documented in the Memory Map section.
Rev. A | Page 22 of 28
AD9434
There are three pins that define the serial port interface (SPI) to this particular ADC. They are the SCLK/DFS, SDIO, and CSB pins. The SCLK/DFS (serial clock) is used to synchronize the read and write data presented to the ADC. The SDIO (serial data input/output) is a dual-purpose pin that allows data to be sent to and read from the internal ADC memory map registers. The CSB is an active low control that enables or disables the read and write cycles (see Table 9). the W0 and W1 bits, which is one or more bytes of data. All data is composed of 8-bit words. The first bit of each individual byte of serial data indicates whether this is a read or write command. This allows the serial data input/output (SDIO) pin to change direction from an input to an output. Data can be sent in MSB or in LSB first mode. MSB first is default on power-up and can be changed by changing the configuration register. For more information about this feature and others, see the AN-877 Application Note, Interfacing to High Speed ADCs via SPI at www.analog.com.
USING THE AD9434 TO REPLACE THE AD9230
The AD9434 can be used to replace the AD9230 in many applications. In these designs, the user should consider these important differences: * Pin 28 is a DNC (do not connect) on the AD9434, and should be left floating. The reset functionality of the AD9230 is not available through an external pin, but is available through the SPI interface. Pin 31 is the interface to the AD9434 reference circuit. It can be used to monitor the internal reference or provide an external reference voltage (nominally 0.5 V). If the internal reference is used, then this pin can float. The RBIAS function of the AD9230 is not necessary with the AD9434. The input voltage range of the AD9434 is nominally 1.5 V p-p, whereas the AD9230 input range is 1.25 V p-p.
HARDWARE INTERFACE
The pins described in Table 9 comprise the physical interface between the programming device of the user and the serial port of the AD9434. The SCLK pin and the CSB pin function as inputs when using the SPI interface. The SDIO pin is bidirectional, functioning as an input during the write phase and as an output during readback. This interface is flexible enough to be controlled by either PROMs or PIC(R) mirocontrollers as well. This provides the user with an alternate method to program the ADC other than a SPI controller. If the user chooses not to use the SPI interface, some pins serve a dual function and are associated with a specific function when strapped externally to AVDD or ground during device poweron. The Configuration Without the SPI section describes the strappable functions supported on the AD9434.
*
*
Table 9. Serial Port Pins
Mnemonic SCLK Function SCLK (serial clock) is the serial shift clock in. SCLK is used to synchronize serial interface reads and writes. SDIO (serial data input/output) is a dual-purpose pin. The typical role for this pin is an input and output depending on the instruction being sent and the relative position in the timing frame. CSB (chip select) is an active low control that gates the read and write cycles.
CONFIGURATION WITHOUT THE SPI
In applications that do not interface to the SPI control registers, the SCLK/DFS pin can alternately serve as a standalone CMOScompatible control pin. In this mode, connect the CSB pin to AVDD, which disables the serial port interface. Table 10. Mode Selection
Mnemonic SCLK/DFS External Voltage AVDD AGND Configuration Twos complement enabled Offset binary enabled
SDIO
CSB
The falling edge of the CSB, in conjunction with the rising edge of the SCLK, determines the start of the framing. An example of the serial timing and its definitions can be found in Figure 52 and Table 11. During an instruction phase, a 16-bit instruction is transmitted. Data then follows the instruction phase and is determined by
Rev. A | Page 23 of 28
AD9434
tDS tS
CSB
tHIGH tDH tLOW
tCLK
tH
SCLK DON'T CARE
DON'T CARE
DON'T CARE
Figure 52. Serial Port Interface Timing Diagram
Table 11. Serial Timing Definitions
Parameter tDS tDH tCLK tS tH tHIGH tLOW tEN_SDIO tDIS_SDIO Min (ns) 5 2 40 5 2 16 16 1 5 Description Setup time between the data and the rising edge of SCLK Hold time between the data and the rising edge of SCLK Period of the clock Setup time between CSB and SCLK Hold time between CSB and SCLK Minimum period that SCLK should be in a logic high state Minimum period that SCLK should be in a logic low state Minimum time for the SDIO pin to switch from an input to an output relative to the SCLK falling edge (not shown in Figure 52) Minimum time for the SDIO pin to switch from an output to an input relative to the SCLK rising edge (not shown in Figure 52)
Table 12. Output Data Format
Input (V) VIN+ - VIN- VIN+ - VIN- VIN+ - VIN- VIN+ - VIN- VIN+ - VIN- Condition (V) < -0.75 - 0.5 LSB = -0.75 =0 = 0.75 > 0.75 + 0.5 LSB Offset Binary Output Mode, D11 to D0 0000 0000 0000 0000 0000 0000 1000 0000 0000 1111 1111 1111 1111 1111 1111 Twos Complement Mode, D11 to D0 1000 0000 0000 1000 0000 0000 0000 0000 0000 0111 1111 1111 0111 1111 1111 OR 1 0 0 0 1
Rev. A | Page 24 of 28
09383-023
SDIO DON'T CARE
R/W
W1
W0
A12
A11
A10
A9
A8
A7
D5
D4
D3
D2
D1
D0
AD9434 MEMORY MAP
READING THE MEMORY MAP TABLE
Each row in the memory map table (see Table 13) has eight address locations. The memory map is roughly divided into three sections: chip configuration register map (Address 0x00 to Address 0x02), transfer register map (Address 0xFF), and ADC functions register map (Address 0x08 to Address 0x2A). The Addr. (Hex) column of the memory map indicates the register address in hexadecimal, and the Default Value (Hex) column shows the default hexadecimal value that is already written into the register. The Bit 7 (MSB) column is the start of the default hexadecimal value given. For example, Hexadecimal Address 0x2A, OVR_CONFIG, has a hexadecimal default value of 0x01. This means that Bit 7 = 0, Bit 6 = 0, Bit 5 = 0, Bit 4 = 0, Bit 3 = 0, Bit 2 = 0, Bit 1 = 0, and Bit 0 = 1, or 0000 0001 in binary. The default value enables the OR output. Overwriting this default so that Bit 0 = 0 disables the OR output. For more information on this and other functions, consult the AN-877 Application Note, Interfacing to High-Speed ADCs via SPI(R) at www.analog.com. Table 13. Memory Map Register
Addr. (Hex) Register Name Chip Configuration Registers 00 CHIP_PORT_CONFIG Bit 7 (MSB) 0 Bit 6 LSB first Bit 5 Soft reset Bit 4 1 Bit 3 1 Bit 2 Soft reset Bit 1 LSB first Bit 0 (LSB) 0 Default Value (Hex) 0x18 Default Notes/ Comments The nibbles should be mirrored by the user so that LSB or MSB first mode registers correctly, regardless of shift mode. Default is a unique chip ID, different for each device. This is a readonly register. Child ID used to differentiate graded devices. Synchronously transfers data from the master shift register to the slave. Determines various generic modes of chip operation.
RESERVED LOCATIONS
Undefined memory locations should not be written to other than with the default values suggested in this data sheet. Addresses that have values marked as 0 should be considered reserved and have a 0 written into their registers during power-up.
DEFAULT VALUES
Exiting out of reset, critical registers are preloaded with default values. These values are indicated in Table 13. Other registers do not have default values and retain the previous value when exiting reset.
LOGIC LEVELS
An explanation of various registers follows: "Bit is set" is synonymous with "bit is set to Logic 1" or "writing Logic 1 for the bit." Similarly, "clear a bit" is synonymous with "bit is set to Logic 0" or "writing Logic 0 for the bit."
01
CHIP_ID
8-bit chip ID, Bits[7:0] = 0x6A
Read only
02
CHIP_GRADE
0
0
0
Speed grade: 00 = 500 MSPS 01 = 370 MSPS 0 0
X1
XX1
X1
Read only
Transfer Register FF DEVICE_UPDATE
0
0
0
0
0
SW transfer
0x00
ADC Functions Registers 08 Modes
0
0
PDWN: 0 = full (default) 1= standby
0
0
Internal power-down mode: 000 = normal (power-up, default) 001 = full power-down 010 = standby 011 = normal (power-up) Note that external PDWN pin overrides this setting
0x00
Rev. A | Page 25 of 28
AD9434
Addr. (Hex) 10 Register Name Offset Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 8-bit device offset adjustment [7:0] 0111 1111 = +127 codes 0000 0000 = 0 codes 1000 0000 = -128 codes Reset PN9 gen: 1 = on 0 = off (default) Bit 1 Bit 0 (LSB) Default Value (Hex) 0x00 Default Notes/ Comments Device offset trim: codes are relative to the output resolution. When set, the test data is placed on the output pins in place of normal data. Set pattern values: P1 = Reg 0x19, Reg 0x1A P2 = Reg 0x1B, Reg 0x1C.
0D
TEST_IO
(For user-defined mode only, set Bits[3:0] = 1000) 00 = Pattern 1 only 01 = toggle P1/P2 10 = toggle P1/0000 11 = toggle P1/P2/ 0000
Reset PN23 gen: 1 = on 0 = off (default)
0F
AIN_CONFIG
0
0
0
0
14
OUTPUT_MODE
0
0
0
15
OUTPUT_ADJUST
0
0
0
Output enable: 0= enable (default) 1= disable 0
Output test mode: 0000 = off (default) 0001 = midscale short 0010 = +FS short 0011 = -FS short 0100 = checkerboard output 0101 = PN23 sequence 0110 = PN9 0111 = one/zero word toggle 1000 = user defined 1001 = unused 1010 = unused 1011 = unused 1100 = unused (Format determined by OUTPUT_MODE) 0 0 0 Analog input disable: 1 = on 0 = off (default) Data format select: Output DDR: 00 = offset binary invert: 1= (default) 1 = on enabled 01 = twos 0 = off 0= complement disabled (default) 10 = Gray code (default) LVDS course adjust: 0= 3.5 mA (default) 1= 2.0 mA 0 0 LVDS fine adjust: 001 = 3.50 mA 010 = 3.25 mA 011 = 3.00 mA 100 = 2.75 mA 101 = 2.50 mA 110 = 2.25 mA 111 = 2.00 mA 0 0
0x00
0x00
0x00
0x00
16
OUTPUT_PHASE
17
FLEX_OUTPUT_DELAY
Output clock polarity 1= inverted 0= normal (default) 0
0
0
0
0x00
0
0
0
Output clock delay: 0000 = 0 0001 = -1/10 0010 = -2/10 0011 = -3/10 0100 = reserved 0101 = +5/10 0110 = +4/10 0111 = +3/10 1000 = +2/10 1001 = +1/10
0x00
Shown as fractional value of sampling clock period that is subtracted or added to initial tSKEW, see Figure 2
Rev. A | Page 26 of 28
AD9434
Addr. (Hex) 18 Register Name FLEX_VREF Bit 7 (MSB) Bit 6 VREF select 00 = internal VREF (20 k pull-down) 01 = import VREF (0.59 V to 0.8 V on VREF pin) 10 = export VREF (from internal reference) 11 = not used B7 B7 B7 B7 0 B6 B6 B6 B6 0 Bit 5 0 Bit 4 Bit 3 Bit 2 Bit 1 Input voltage range setting: 11100 = 1.60 00101 = 1.36 11101 = 1.58 00110 = 1.34 11110 = 1.55 00111 = 1.31 11111 = 1.52 01000 = 1.28 00000 = 1.50 01001 = 1.26 00001 = 1.47 01010 = 1.23 00010 = 1.44 01011 = 1.20 00011 = 1.42 01100 = 1.18 00100 = 1.39 B3 B2 B1 B0 B3 B3 B3 0 B2 B2 B2 0 B1 B1 B1 OR position (DDR mode only): 0= Pin 9, Pin 10 1= Pin 21, Pin 22 0 Bit 0 (LSB) Default Value (Hex) 0x00 Default Notes/ Comments
19 1A 1B 1C 2A
USER_PATT1_LSB USER_PATT1_MSB USER_PATT2_LSB USER_PATT2_MSB OVR_CONFIG
B5 B5 B5 B5 0
B4 B4 B4 B4 0
0x00 0x00 0x00 0x00 0x01
B0 B0 B0 OR enable: 1 = on (default) 0 = off
User-defined pattern, 1 LSB. User-defined pattern, 1 MSB. User-defined pattern, 2 LSBs. User-defined pattern, 2 MSBs.
2C
Input coupling
0
0
0
0
0
DC coupling enable
0
0x00
Default is ac coupling.
1
X = don't care.
Rev. A | Page 27 of 28
AD9434 OUTLINE DIMENSIONS
8.10 8.00 SQ 7.90 0.60 MAX 0.60 MAX
43 42
0.30 0.23 0.18
56 1
PIN 1 INDICATOR
PIN 1 INDICATOR
7.85 7.75 SQ 7.65
0.50 BSC
EXPOSED PAD
5.25 5.10 SQ 4.95
14 29
TOP VIEW 1.00 0.85 0.80 SEATING PLANE 12 MAX 0.80 MAX 0.65 TYP
0.50 0.40 0.30 0.05 MAX 0.02 NOM COPLANARITY 0.20 REF 0.08
28
15
BOTTOM VIEW 6.50 REF
0.25 MIN
FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET.
081809-B
COMPLIANT TO JEDEC STANDARDS MO-220-VLLD-2
Figure 53. 56-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 8 mm x 8 mm Body, Very Thin Quad (CP-56-5) Dimensions shown in millimeters
ORDERING GUIDE
Model1 AD9434BCPZ-370 AD9434BCPZRL7-370 AD9434BCPZ-500 AD9434BCPZRL7-500 AD9434-370EBZ AD9434-500EBZ
1
Temperature Range -40C to +85C -40C to +85C -40C to +85C -40C to +85C
Package Description 56-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 56-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 56-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 56-Lead Lead Frame Chip Scale Package [LFCSP_VQ] LVDS Evaluation Board with AD9434BCPZ-370 LVDS Evaluation Board with AD9434BCPZ-500
Package Option CP-56-5 CP-56-5 CP-56-5 CP-56-5
Z = RoHS Compliant Part.
(c)2011 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D09383-0-5/11(A)
Rev. A | Page 28 of 28

▲Up To Search▲

Price & Availability of AD9434BCPZ-370

	To Download AD9434BCPZ-370 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .